| 741 | 3 | 279 |
| 下载次数 | 被引频次 | 阅读次数 |
含软弱夹层倾斜结构面的剪切特性与倾斜角、充填度密切相关,为了获得具有起伏形貌的含软弱夹层倾斜结构面的剪切特性,采用多功能岩土体接触破损测试系统,开展了针对起伏形貌的含软弱夹层倾斜结构面试样的直剪试验。试验结果表明:(1)不含软弱夹层的倾斜结构面剪应力–剪切位移曲线具有峰值剪断特征;含软弱夹层倾斜结构面剪应力–剪切位移曲线具有滑动破坏特征。(2)充填度不同时,倾斜结构面法向位移随剪切位移增大而增大,变化率逐渐增大并趋于稳定,呈剪胀效应特征;倾斜角不同时,结构面法向位移均随着剪切位移的增大而增大,并且法向位移前期增长率明显小于后期增长率。(3)倾斜结构面抗剪强度随充填度的增大呈负指数减小;随倾斜角和法向应力的增大近似呈线性增大。(4)考虑软弱夹层材料、充填度及倾斜角对抗剪强度的影响,在Barton抗剪强度模型的基础上,建立了适用于含软弱夹层倾斜结构面抗剪强度模型。研究成果可为工程岩体稳定性评价提供参考。
Abstract：The shear behavior of inclined rock joint containing weak interlayers are closely related to the dip angle and degree of infill. To obtain the shearing characteristics of inclined rock joint with undulating morphologies containing weak interlayers, direct shear tests were conducted on samples of inclined rock joint with such morphologies using a multifunctional geotechnical contact-destruction testing system. The results show that the shear stress-shear displacement curves of inclined rock joint without weak interlayers exhibit peak shear fracture characteristics, while those containing weak interlayers show sliding failure characteristics. Under varying degrees of infill, the normal displacement of inclined rock joint increases with increased shear displacement, with the rate of change gradually increasing and stabilizing, showing a dilation effect. Under different dip angles, the normal displacement of rock joint with shear displacement, and the early growth rate of normal displacement is significantly less than the latter. The shear strength of inclined rock joint shows a negative exponential decrease with increasing degree of infill, an approximately linear increase with an increasing dip angle, and an approximate linear increase with increasing normal stress. Considering the impact of weak interlayer material, degree of infill, and dip angle on shear strength, a new model for shear strength suitable for inclined rock joint containing weak interlayers was established based on the Barton shear strength model. The research findings can provide a reference for evaluating the stability of engineering rock masses.
[1]罗战友,杜时贵,黄曼.岩石结构面峰值摩擦角应力效应试验研究[J].岩石力学与工程学报,2014,33(6):1142-1148.LUO Zhanyou,DU Shigui,HUANG Man.Experimental study of stress effection peak friction angle of rock structural plane[J].Chinese Journal of Rock Mechanics and Engineering,2014,33(6):1142-1148.
[2]BARTON N.Review of a new shear-strength criterion for rock joints[J].Engineering Geology,1973,7(4):287-332.
[3]BARTON N,CHOUBEY V.The shear strength of rock joints in theory and practice[J].Rock Mechanics,1977,10:1-54.
[4]袁伟,李建春.剪切速率对平直节理摩擦行为的影响及其机制研究[J].岩石力学与工程学报,2021,40(S2):3241-3252.YUAN Wei,LI Jianchun.Study on the effects and its mechanism of shear rate on friction of planar joints[J].Chinese Journal of Rock Mechanics and Engineering,2021,40(S2):3241-3252.
[5]杜时贵,吕原君,罗战友,等.岩体结构面抗剪强度尺寸效应联合试验系统及初级应用研究[J].岩石力学与工程学报,2021,40(7):1337-1349.DU Shigui,LYU Yuanjun,LUO Zhanyou,et al.Combined test system for size effect of rock joint shear strength and its primary application research[J].Chinese Journal of Rock Mechanics and Engineering,2021,40(7):1337-1349.
[6]HUANG M,HONG C,DU S,et al.Experimental technology for the shear strength of the series-scale rock joint model[J].Rock Mechanics and Rock Engineering,2020,53:5677-5695.
[7]ZHANG X,LI Y,WANG J.Influence of infill material on the shear strength of rock joints[J].International Journal of Rock Mechanics and Mining Sciences,2018,103:45-56.
[8]CHEN L,ZHAO Z.Effects of joint inclination on the mechanical behavior of rock masses with weak interlayers[J].Engineering Geology,2019,250:1-12.
[9]张晓悟,徐金海,刘智兵,等.不同加载路径条件下软弱夹层泥岩力学响应及变形规律[J].采矿与岩层控制工程学报,2021,3(4):043022.ZHANG Xiaowu,XU Jinhai,LIU Zhibing,et al.Mechanical response and deformation of weak interbedded mudstone under different loading paths[J].Journal of Mining and Strata Control Engineering,2021,3(4):043022.
[10]朱俊福,尹乾,张京民,等.深部缓倾软弱夹层巷道围岩变形演化与非对称支护[J].采矿与岩层控制工程学报,2022,4(5):053031.ZHU Junfu,YIN Qian,ZHANG Jingmin,et al.Deformation evolution and asymmetric support of deepburied surrounding rock mass with a gently inclined weak interlayer[J].Journal of Mining and Strata Control Engineering,2022,4(5):053031.
[11]吴旭平,杨新安,李亚翠,等.含软弱夹层浅埋隧道变形特性及控制指标研究[J].岩石力学与工程学报,2014,33(S1):2685-2691.WU Xuping,YANG Xin'an,LI Yacui,et al.Research on control indices and deformation characteristic of shallow tunnel with weak interlayer[J].Chinese Journal of Rock Mechanics and Engineering,2014,33(S1):2685-2691.
[12]GOODMAN R E.The deformability of joint[A].Determination of the In-situ Modulus of Deformation of Rock[C].West Conshohocken:ASTM International,1970:174-196.
[13]PEREIRA J P.Shear strength of filled discontinuities[A].Proceedings of the International Conference on Rock Joint[C].Loen,1990:283-287.
[14]LIU H,SUN Q.Engineering considerations for infilled weak interlayers in construction[J].Journal of Geotechnical and Geoenvironmental Engineering,2020,146(6):04020045.
[15]INDRARATNA B,PREMADASA W,BROWN E T.Shear behaviour of rock joint with unsaturated infill[J].Géotechnique,2013,63(15):1356-1360.
[16]INDRARATNA B,PREMADASA W,BROWN E T,et al.Shear strength of rock joint influenced by compacted infill[J].International Journal of Rock Mechanics and Mining Sciences,2014,70:296-307.
[17]曾纪全,杨宗才.岩体抗剪强度参数的结构面倾角效应[J].岩石力学与工程学报,2004,23(20):3418-3425.ZENG Jiquan,YANG Zongcai.Dip effect of structural plane on shearing strength parameters of rock mass[J].Chinese Journal of Rock Mechanics and Engineering,2004,23(20):3418-3425.
[18]王瑞红,邓捷,刘杰,等.节理对砂岩变形及破坏特征影响研究[J].地下空间与工程学报,2017,13(1):93-100.WANG Ruihong,DENG Jie,LIU Jie,et al.Influence of joint on deformation and failure characteristics of sandstone[J].Chinese Journal of Underground Space and Engineering,2017,13(1):93-100.
[19]邓华锋,潘登,许晓亮,等.三轴压缩作用下断续节理砂岩力学特性研究[J].岩土工程学报,2019,41(11):2133-2141.DENG Huafeng,PAN Deng,XU Xiaoliang,et al.Mechanical characteristics of intermittent jointed sandstone under triaxial compression[J].Chinese Journal of Geotechnical Engineering,2019,41(11):2133-2141.
[20]金爱兵,陆通,王本鑫,等.基于改进力学等效的岩体关键节理倾角特征试验研究[J].岩石力学与工程学报,2023,42(1):76-87.JIN Aibing,LU Tong,WANG Benxin,et al.Experimental study on the dip characteristics of key joints in rock mass based on improved mechanical equivalence[J].Chinese Journal of Rock Mechanics and Engineering,2023,42(1):76-87.
[21]雷霆,夏磊,王秋良,等.层状岩体的颗粒流模拟新方法及数值分析[J].科学技术与工程,2017,17(2):256-261.LEI Ting,XIA Lei,WANG Qiuliang,et al.A new method to simulate the layered rock mass and the numerical analysis[J].Science Technology and Engineering,2017,17(2):256-261.
[22]刁杨龙.节理岩体变形破裂机制的宏细观试验研究[D].邯郸:河北工程大学,2021.DIAO Yanglong.Macro-meso experimental study on deformation and failure mechanism of jointed rock mass[D].Handan:Hebei University of Engineering,2021.
[23]宋彦琦,李名,刘江,等.含不同倾角天然软弱夹层的大理岩破坏试验[J].中国矿业大学学报,2015,44(4):623-629.SONG Yanqi,LI Ming,LIU Jiang,et al.Experimental test on marble containing natural weak interlayer of different angles[J].Journal of China University of Mining&Technology,2015,44(4):623-629.
[24]刘明星,廖孟柯,刘恩龙,等.不同结构面倾角节理岩体三轴试验力学特性[J].北京工业大学学报,2018,44(3):336-343.LIU Mingxing,LIAO Mengke,LIU Enlong,et al.Experimental research on mechanical properties of jointed rock mass with different angles of inclination[J].Journal of Beijing University of Technology,2018,44(3):336-343.
[25]彭岩岩,周崇,程啸,等.不同节理倾角下灰岩应变场演化及裂纹发展规律[J].采矿与岩层控制工程学报,2023,5(4):043528.PENG Yanyan,ZHOU Chong,CHENG Xiao,et al.Evolution of strain field and crack development of limestone under different joint inclination angles[J].Journal of Mining and Strata Control Engineering,2023,5(4):043528.
[26]汪丁建.含节理层状岩石破裂特性及边坡工程应用研究[D].武汉:中国地质大学,2019.WANG Dingjian.Fracturing behaviors of the bedded rocks containing structural flaws with application to slope engineering[D].Wuhan:China University of Geosciences,2019.
[27]LADANYI B,ARCHAMBAULT G.Shear strength and deformability of filled indented joint[A].Proceedings of International Symposium on Geotechnics of Structurally Complex Formations[C].Capri,1977:317-326.
[28]张全恒.岩石结构面抗剪强度的确定[J].岩土工程学报,1992,14(S1):113-119.ZHANG Quanheng.Determination of shear strength along rock stratum plane[J].Chinese Journal of Geotechnical Engineering,1992,14(S1):113-119.
[29]邹宗兴,唐辉明,刘晓,等.制样误差对结构面直剪试验结果影响定量研究[J].岩石力学与工程学报,2010,29(8):1664-1669.ZOU Zongxing,TANG Huiming,LIU Xiao,et al.Quantitative study of structural plane direct shear test results influenced by sample preparation errors[J].Chinese Journal of Rock Mechanics and Engineering,2010,29(8):1664-1669.
[30]刘维明,王昌硕,张希巍,等.考虑非平稳趋势向影响的结构面抗剪强度模型研究[J].岩石力学与工程学报,2023,42(2):378-390.LIU Weiming,WANG Changshuo,ZHANG Xiwei,et al.Study on the shear strength model of rock joints considering the influence of non-stationary trend[J].Chinese Journal of Rock Mechanics and Engineering,2023,42(2):378-390.
[31]YANG Haiqing,LIU Junfeng,LIU Bolong.Investigation on the cracking character of jointed rock mass beneath TBM disc cutter[J].Rock Mechanics and Rock Engineering,2018,51:1263-1277.
[32]LADANYI B,ARCHAMBAULT G.Shear strength and deformability of filled indented joints[A].Proc International Symposium on the Geotechnics of Structurally Complex Formations[C].Capri,1977:317-326.
基本信息:
DOI：10.13532/j.jmsce.cn10-1638/td.2024.05.004
中图分类号:TD315
引用信息:
[1]罗战友,付秀祥,杜时贵,等.软弱夹层倾斜结构面剪切试验及抗剪强度模型研究[J].采矿与岩层控制工程学报,2024,6(05):57-67.DOI:10.13532/j.jmsce.cn10-1638/td.2024.05.004.
基金信息:
国家自然科学基金资助项目(42277147,42272333)